Accuracy Systems, Inc. Click for the BBB Business Review of this Guns & Gunsmiths in Byers CO 1661 Behrens RD
Byers, Colorado 80103
Tel: (303) 822-6849 Fax: (720) 367-5095
E-Mail Us at accuracyinc1@aol.com
Accuracy Systems' location is not a retail/store front. It is a machine shop with dangerous machines running. For your safety we do not accept walk-ins. PLEASE CALL FOR AN APPOINTMENT IF YOU ARE GOING TO VISIT. THANKS.

PRICES SUBJECT TO CHANGE WITHOUT NOTICE!

Barrel Break-In Procedures

Thank you for you purchase of an Accuracy Systems Barrel Conversion. While all of our barrels are of high quality, a new barrel will shoot best if careful attention is given to proper break-in. The bore of your new barrel has “pores” and as you break in the barrel these “pores” are smoothed over. A smooth barrel always cleans up better than one that isn’t.

Equipment needed:

Break-In Procedures:
  1. Load your rounds in the magazine and insert into the rifle. After your last shot the action will stay open allowing for the bore snake to be dropped through the breech end and pulled out the muzzle. Then remove the empty magazine and load the next magazine into the rifle. This is the fastest method.
  2. Clean barrel after each 3 shot group for the first 60 shots or more if needed. Use one of the Bore snakes with the JB Bore Compound mentioned above. Put the compound in bush area of the snake. Pull the bore snake through the rifle from chamber to muzzle 2 times. Follow that up by pulling the clean, dry, second snake through 1 time. We also recommend 0000 steel wool wrapped around the brush area only this will help lap the barrel even further reducing fouling and speeding the barrel break in. Make sure you use the JB Compound liberally on the steel wool! It is not needed behind the brush area.
  3. Check to see if there is any visible copper fouling. The barrel will have an orange or brown tint inside the barrel if it is fouled. If copper is visible repeat the pull through process a few extra times. REPEAT TILL ALL COPPER IS GONE!
    NOTE: If Bore snake is used for different chemicals make SURE to completely clean it with the brake cleaner to remove any cleaning solvent from step 1. Mixing of chemicals could have an adverse effect on the barrel. Three bore snakes are recommended for ease of break in. After brake cleaner has been applied to the bore snake, wring it out to remove the excessive brake cleaner. You may have to repeat this process until the snake is completely clean. Allow the bore snake to dry out. It should evaporate with in about 15 minutes in direct sun light.
  4. For the next 30 shots, Clean the barrel after each 3 shot group following the above initial break in procedures. The Barrel should be finished with the break in process after 90 rounds. However if you still notice fouling you may have to continue the process until fouling is at a minimum.
  5. Revert to your normal cleaning schedule. Make sure to continue to always clean your barrel during and after each outing to insure the optimum accuracy out of your rifle.
**The beauty of brake parts cleaner verses Gun Scrubber™ is that the brake cleaner can be found at any automotive store at ½ the cost of the Gun Scrubber™. Brake parts cleaner works just as well and dries just as fast. Thank you, Accuracy Systems Inc.

PRICES SUBJECT TO CHANGE WITH OUT NOTICE!

Thursday, March 28, 04:29:57 PM Mountain Time

Accuracy Systems' location is not a retail/store front. It is a machine shop with dangerous machines running. For your safety we do not accept walk-ins. PLEASE CALL FOR AN APPOINTMENT IF YOU ARE GOING TO VISIT. THANKS.

Hours of operation are Monday thru Thursday 8:30 AM to 4:30 PM, Friday 8:00 AM to 12:00 PM Mountain Time Zone
(Closed Saturday & Sunday)

All prices stated in this web site are subject to change without notice.

Hosted, Maintained, Promoted, & Optimized for Search Engine Placement by Hosting Texas
Contact the Webmaster

Links to our favorite gun related sites. - Site Map

Old Tree Gun Blanks - Gun News Daily - Gun News Daily's Holsters - Body Armor - Mike Niles Outfitting - OutfitterPros.com - Gun Safes - New Mexico Elk Hunting - Antelope Hunting

Copyright © 2007 Accuracy Systems Inc.

Number of visitors to this page so far: 3425