ACCESSORIES
Epoxy Barb Hinges
1.6mm epoxy board hinges drilled for 16swg wire pin.
Use 2 or 3 per hinge point.
( 3 to prevent side to side movement.)
Glue parts into each side of the hinge line using
piano wire pin to line them all up.
Pin slides out for building & maintanance. Retain pin
by gluing bent end or solder tag to take a screw.
£0.50 each barb.
|
 Barb hinge for big spitfire tail
(left ) & elevator (right).
Narrow barb for a 1.6mm wide x 5mm high slot.
wide barb for a 10mm high slot or drilled hole.
|
|
Self adhesive vinyl decals.
colours similar to our paints, rings are separate.
spitfire sets
include a selection of grey squadron & black serial
letters.
1/4 spitfire £40
1/5 spitfire £30
1/6 spitfire £22
1/6 Hurricane £22
1/7 FW 190 £6
1/6 Venom £10
1/3 Camel £45
1/3 Pup £45
1/3 Sopwith Triplane £50
1/4 Camel £35
1/4 Pup £35
|
 Steel plates.
Plated Steel 36 mm x 5.5 mm
Stainless Steel 36mm x 6mm
2mm holes.
£3 pkt 8. .
1/4 scale oxygen hose. £1 a foot.
|
 Small Turnbuckles. .
Steel.
M2
thread. out of stock
|
A job saved is money well spent.
Epoxy
Horns
| 2 1/2 inch
|
£2.50 each |
£4.50 a pair |
£9 pack of 4 |
| 2
inch |
£2 each |
£3.50 a pair |
£7 pack of 4 |
| 1.1/2 inch |
£ 2 each |
£3 a pair |
£6 pack of 4 |
| 1 1/4 inch |
£2 each |
£3 a pair |
£6 pack of 4 |
| servo arms |
£2 each |
|
|
|
|
|
 Tiny brass hinges. 8 mm x 10 mm
(3/8" x 5/16"). £2 packet of four
Great for scale hatches and doors etc.
Use screws E (top), or F (lower) £1.50 pkt 30
Also brass nails to simulate roundhead rivets 2mm diam
head. £1.50 pkt 40
You will want the smallest from our crosshead screwdriver
set, £3
And our 0.8 mm drill £1.
|
 Mini snap hinges. £1
Brass finish. 3 inches wide.
Can be cut for shorter hinge. Snap open and snap shut.
No hatch catch needed.
Spring can be removed for normal action.
|
You can lead a horse to water, but you can't make
it pass water!
 Sliding canopy rails.
12 inch long brass. £6 each
3/16" (5mm) square.
Slot takes an M2 screw head which slides smoothly along.
Solder two screws each side to your canopy frame.
Cut round holes in the rail at about half way open so the
frame
can be sprung apart and the canopy taken off.
Dont forget you will need the rails to be
twice the lenght of your canopy.
Polypropolene rail runners 10mm long, 2mm self tapping
screw,
drill through metal frame & canopy edge, fit 2 or 3
each side.
6 runners £3
bag of 30 screws £2
|
Alloy SPINNERS
6" diam x 6 1/2" long for
1/4 Spitfire £75
5" diam x 4.5" long Mosquito -£45
5" diam x 5" long Hurricane £75
4" x 4" 1/6 Spitfire £25. -4
BLADE SCALE DISPLAY PROP KIT
1/6 for Spitfire.
£12 1/4 scale
£25
blades also good for Hurricane etc.
See my model on spitfire page.
|
 Wing joining tubes.
Aluminium tubes with matching
phenolic outer tube.
1" x 36" £28.
3/4" x 36". £25.
1/2" x 36", £20
|
Super Carbon spinner.Lightweight and strong.
6"- £85 out of
stock. .........5" - out of stock
|
| SCALE RIVETS SYSTEM Scale Diameter
x Pitch or spacing
price
1/7 scale (1 mm x 2.8mm ) £8
1/6 scale (1.2 mm x 3.3mm ) £8
1/5 scale (1.5mm x 4 mm pitch) £8
1/4 scale (1.8 mm x 5mm
) £10
1/3 scale (2.4mm x 6.6 mm
) £12
metalcoat applied over vinyl rivets
|
Scale rivets 12
inch long strips. 50 rivets per strip.
24 strips = 1200 rivets.
Each rivet yields two heads = 2400 rivets.
Two rivet types; self adhesive & painted..
Painted rivets. Stick the self adhesive strip to
the model.
Use a small brush to apply primer or paint to the holes
in the strip. Peel off the strip when paint has dried.
(Only 2 minutes with primer). Now ready for painting.
Stuck-on rivets.
Peel off the outer strip ( save this for painted rivets).
Apply adhesive tape over the dots on the paper,
rub down hard with knife handle and lift off.
Apply the tape to the model, rub down and remove the
tape.
The adhesive dots are ready to be painted with the model.
The stuck-on rivets are slightly smaller than the painted
type and stand out more on the surface.
The painted type depend on how thick you apply the paint.
Practice on plastic sheet with both types, then paint
them to see if the result suits the model you are
building.
Experiment to get the right effect.
.Scale paneling tapes
£3.50 pack. 120 x
9 inch strips.
Stick the tapes to
the model, spray over with primer.
A light sanding then removethe tapes.
Leaves a very narrow groove to simulate panel
lines. Should be done before the rivets.
Self adhesive silver
vinyl sheet,
12" x 24" £3
Use for scale hatches etc.
 MRM
Rivets on my Hurricane
|
Foam for making scale tyres.
Very light. Black.
Soft 2 3/8" x 12 x 12. £20
Hard 1 3/4" x 12 x 12" £25 (black or grey
available)
Hard 1.2" x 12" x 12" £20
12" x 12" square. Will make two 6" and
two 5" tyres,
or two 6 1/2" and two 4 1/2" tyres.
Mark a circle 3 mm oversize. Drill centre hole and saw
to rough shape.Mount on a bolt and fit in electric drill.
Sand to shape with coarse, then fine paper.
Make the hub with brass tube, washers each side and
long bolts to pull together, or to suit the particular
scale
appearance. The foam gives good performance
and will take a good weight.
Grey suitable for some ww1 aircraft.
|
. Servo plug holder
This handy item to allow you to fix your servo lead on
the
side of the fuselage, so that the aileron lead can be
easily
connected. It can also be used in other places where it
makes plugging in a servo a one handed operation.
Only
50p each.
|
 SCALE RIB TAPES
Based on the full-size 2" wide,
5 points per inch, we have;-
1/3 scale, 0.66" x15 PPI.
1/4 scale, 0.5" x 20 PP
1/5 scale, 0.4" x 25 PPI
1/6 scale, 0.33" x 25 PPI
Each set has 20 strips x 24" long, plus 4 double
& 2 half width.
2 layers are cut together, please peel apart before use.
£25 in oratex antique
(also in
silver, olive drab.)
We can cut in any other colour, just send us your
material.
These are not 'pinking' tapes but 'pinked tapes'
Customers comments - Mick Reeves tapes are the best, very
thin,
look very scale, stretch easily round curves, adhere
well.
Dummy rib stitching
To go under the rib tapes.
Lift with the point of a knife and apply. 300 pieces .£2
36 CIRCLES (12 big/middle/small),
say which scale you want.£15
.
Oratex 24" wide ( 600mm)
10 meter roll £154
2 meter roll £34
Oratex glue (same as Balsaloc) £12.60
|
 BRASS TUBE. 12" long.
each fits inside the next size.
1/16" £1.50.
3/8"
£5.50
3/32" £1.50.
13/32"
£6
1/8" £2.50.
7/16"
£7
5/32" £2.50.
15/32"
£ 7
3/16" £2.75.
1/2"
£7
7/32" £3.00.
17/32"
£ 7.50
1/4" £4.
9/16"
£7.5
9/32" £4.
19/32"
£8.50
5/16" £4.50
5/8"
£8.50
11/32" £4.50..........................
Brass tubes to fit piano wire gauges.
6g, 10g. 12g. 16g. 18g. .
All 12". £1.50.
1/4" o/d mild steel tube x 15 inch length. £3
8mm x 1.6mm wall axle tube any length £2 per 10cm, .
10mm x 2mm wall axle tube , any length £3 per 10cm
Razor blade strips. 50p each.
Epoxy board. Useful for
horns and fittings.
.
1.6 mm. 6" x 12" - £9
5 mm - £20 per square foot.
INSTRUMENT PANEL KITS
For WW2 British fighters. semi
scale Spitfire or Huricane.
1/7 scale -120mm wide,. 1/6 - 138mm,. 1/5 - 165mm £6 .
1/4 scale - 207mm £7.
1/3 scale - 275mm£10.
Can be assembled in half an hour. See also Sopwith page.
MRM
|
METALCOAT
Real sheet aluminium for model covering. 0.05mm
thick.
Self adhesive, Only weighs 9.4 gm per sq foot. (100g /m2)
.Easy finish - stick it on, ready to paint,
polish or burnish to required effect. will form to
compound curves.
Of course its fuelproof. Easily replace a patch if
damaged.
600 mm wide. £6 per metre
Jims
model
Tony
Manzur's P51
|
This 1/6 scale sergeant pilot (unpainted)
£5
1/4
scale Mick, age 32!
£5 
1/4 scale. Colonel Blimp. £16 - rotary cast
.
1mm or 0.5mm clear plastic for glazing. 8" x
22" £5
|
P47 Thunderbolt with metalcoat finnish;
https://www.rcuniverse.com/forum/rc-warbirds-warplanes-200/11206651-newly-finished-carf-p-47-thunderbolt.html
Ian Redshaw's DH2 with 30" pusher prop on
Torquemaster with 9" extended shaft
|
.
Chipmunk instrument panel kit. £12
- 112mm wide x 60mm high
- 135 mm x 72
-140mm x75
-167mm x 92
Can be assembled in half an hour..
MRM
|
 Sopwith Swallow by Fernando Blanco
|
 My
glow system for Laser twin. Each plug needs only 1.2
volts for easy starting!
On board two cell NMH 2000 mah. The throttle servo switch
comes on at low throttle only.
The RUN switch is on for nornal start/ fly.
Three jack sockets are fitted.
1. Charge on board battery.
2. Test amps. with run switch off, this connects the on
board battery and displays amps on a grond support box.
Tells you the
state of charge and that the plugs are both working.
3. Connects the 2 volt ground battery if the on board
fails. Engine will start, then run without a battery.
This saved me losing a flight at
a World Champs.
|
|
| |
|
|
Tiny screws F, One of our most useful
and unique items.
Opens up new possibilities for scale models
Hinges, canopies, and scale fittings can be held in place
with screws instead of gluing on.
Easier to service and more realistic.
I also use them for practical things, mounting servos,
rigging brackets, hinges, etc.etc.
Buy a packet to try.
Items M,N, P fit our forkends. PLEASE ORDER BY LETTER
CODE.
|
 |
|
|
 |
6 BA x 1" bolts £1 per 100! |
U
1.5 x 5 mm
Round crosshead
£2
pkt 30 |
|
0.8 mm Pilot drill
for tiny screws. £1 |
|
metal ball links.
. M3. £2.50
8 Prong nuts. M3 or M4..£2
 M2 , M3 Cable
anchors. 75p.
Tiny Eyelets.,for fabric, lacing.
£1 pkt 100
(3mm O/D, 2mm body , 1.6mm bore, 3mm long)
Metal Quick Links.
M2 or M3 £1 each
M2 or M3 threaded rods 60p each
Kevlar thread.
0.038". (1mm) 10 metres £5.
Very strong. No stretch. . Yellow, but can
be dyed or painted.
Use for closed loop controls,
no radio sheilding effects.
 >
0.4mm silver grey Kevlar 10m £5.
half a gram per meter.
Light control cable, stainless
steel. 49 strand.
5 meters £5
0.5mm, 0.6 mm, 0.8 mm, 1.0 mm
Heavy cable, soft, 49 strand, for all larger
models.
1.2 mm or 1.5 mm. 5 metres £6 .
1 mm cheap cable. not as
flexible. 25p/metre.
|
|
Metal fuel Filter £3
Air pressure gauge.
1/2 inch diameter. £20
Fine quality Silver Solder. 55%
real silver.Very strong.
1/32" diameter for delicate work. approx 24"
long. £3.50
flux 50p
Silver soldering tips.
1. No need to clean our rigging wire,. screws, bendy
pipe, etc.
2. Use a brick as a base, rig the parts in position.
3. Mix a little flux with a few drops of water, not too
much water.
4. Apply the flux carefully to the joint. The solder will
flow on the
areas with flux, nowhere else, so wipe away any flux in
places it is not needed.
5. Lay pieces of solder on the joint. For circular parts,
roll
solder into rings to fit.
6. Apply the blowlamp to the joint. If one part is
thicker, keep the
flame on the thicker part, so that the thin part is not
over heated.
7. The solder should flow with the parts just below red
heat,
but it will still work if some parts do be come red hot.
8. Apply more solder from the stick if needed.
9. If fails to flow on any part, add more flux and try
again.
10. If needed, allow to cool, clean the area and try
again.
11. It is very possible to solder one side of a small
part,
without melting the other side, even on a 6mm pipe for
example.
So, you can tack it on one side, then bend it to close a
gap
on the other side, and finish soldering the joint.
|
Retracts valve with speed control. £35
Light alloy
sheet. 24 swg .
12" x 18". £10
Sopwith nose panels.
Tinplate. Approx 6" x 12" £4
For small brackets, fittings etc.
Brass hatch catch £4.50
|
PRO-SKIN
PRO-SKIN is epoxy-glass sheet which has been moulded under high
pressure and heat.
Result is a perfect flat sheet with semi-matt surface which
accepts paint and glues well.
It is waterproof and fuelproof, and will not warp.
When a model has been covered in PRO-SKIN, it will be ready to
paint!
Gone will be the weeks or months of tedious dusty work of rubbing
down, messy resin/glass
covering, filling, more rubbing down and so on.
PRO-SKIN gives you a representation of a scale metal skin which
would be hard to achieve
normally, and its instant!
When you add it all up, PRO-SKIN is not only MUCH quicker, it is
also cheaper!
CHEAPER THAN PLYWOOD!
Please note that the
thickness stated is nominal.
The process cannot control the thickness exactly and so this will
vary.
PRICES
0.2 mm. - Foam wings
and small models. weight 44 gm sq ft.
1.22m
x 1.22m (48" x 48") £40.
Half
sheet £21.
0.3 mm - Built up
wings. weight 88gm sq
ft
Full
sheet 1.22m x 2.44m ( 4ft x 8 ft ) £110.
Half sheet 1.22 x 1.22m ( 4 ft x 4
ft ) £55
Quater sheet 1.22 x .6m ( 48"
x 24") £28
A4
sheet 8" x 12" £5
1m x 2m ( 39" x 78") out of stock or half sheet £38 .
ProSkin can be rolled up for
posting.
I did a check building a 9 foot span pair of wings,
Balsa sheet £35. 1120 gm
50 gm Glass cloth £15 135 gm
Epoxy resin
£17
200 gm
spray filler
£17
185 gm
sandpaper
£7
Total cost
£91
1640 gm
The cost of eqivalent area in 0.3 ProSkin - £84.
The proskin was a little heavier 1872 gm. but much stronger.
We checked out plywood prices -
Proskin 0.3 mm thick £2.50 Sq Ft.
1/32"plywood (0.8 mm) £3 Sq Ft
1/48" plywood (0.6 mm) £5. Sq Ft
1/64" plywood (0.4 mm) £7. Sq Ft.
So, its Cheaper and much Stronger than ply wood, and is ready to paint!
Use for Foam wings, instead of veneers.
Sheet is applied using Polyurathane adhesive. The adhesive has a
foaming action which
fills the slight irregularities in the foam. Leading edges and
wing tips are best made with balsa as normal.
Result is a hard surface ready to paint.
Wing is strong and stiff as it would have been with the normal
veneer/glass/epoxy resin finish.
Built up wings instead of sheet balsa.
0.2, 0.3, PRO-SKIN is used according to the size of the model.
The wing structure is sanded until all ribs and spars are level,
just as you would for sheeting with balsa.
The PRO-SKIN is cut with scissors slightly oversize.
(One piece covers the wing, no joining of sheets is needed).
Polyurathane adhesive is applied to the wing structure and the
skin is smoothed down and clamped or weighted.
The adhesive foams up to fill any gaps and
also give a filleting effect to make a strong bond with the
structure.
The adhesive will be handleable in about 20 minutes, then the
wing can be lifted and the operation repeated for
the other side. The PRO-SKIN will only work where there is no
double curvature, so wing tips and leading
edges willbe made in the traditional way. The PRO-SKIN is now
ready for painting!
Alternative adhesive is one hour epoxy with
some filler to thicken it.
This allows more time to position the skins.
It is good practice to roughen the ProSkin suface at the glue
joints.
Hunter wing with top skin fitted.
Hunter flap only 6 mm thick and completely rigid.
Took 15 minutes to make.
Fuselages, small assemblies, ailerons etc,
anywhere that a flat sheet will fit.
Perfect sharp and straight trailing edges are easy with PRO-SKIN.
Scale hinging for metal subjects now becomes easy! Hinges can be
fitted with our
tiny screws directly under the thin, hard PRO-SKIN sheet.
Hatches?
Just cut the hatch in PRO-SKIN, place it on the surface and mark
around with a knife.
Cut out, and line the hole with narrow strip of PRO-SKIN glued
inside.
Place the hatch into the perfectly fitted recess and secure with
MRM tiny screws F.
Job done!
How?
Foam wings/tails/fuselage panels are
covered in the thinnest PRO-SKIN, using polyu glue.
You must prepare the job well before applying the adhesive to one
side of the foam,
spreading with a scraper. You must work quickly to get the
PRO-SKIN in place within 5 minutes.
The PRO-SKIN is then held down with the foam wing outer block and
weights, and left to set.
Adhesives.
Polyurathane sticks very well to most things (even your fingers).
It is very convenient to fit formers in glass fuselages because
it needs no mixing.
Just squirt it from the bottle over the joint and it will form a
natural, slightly flexible fillet.
Proskin will work with epoxy resins and cyanos, best to abraid
the surface along the glue lines.
For an almost unbreakable trailing edge, just apply normal cyano
so that it wicks between the wing skins.
It will set in a few minutes, then you will be able to knock the
trailing edge of your wing on the edge
of your wooden bench. The bench will be dented, not the wing!
Limitations.
As you might expect, being a perfect flat board, PRO-SKIN cannot
cover compound curves in one piece.
Most wing panels can be dealt with, and the leading edge is most
easily achieved with balsa in the traditional way.
Double curvature wings may be possible by slitting the PRO-SKIN
near the wing tip,
but you must experiment with this. Wings with a change in
section, such as the Hunter or Javelin
will require a short slit at the front of the ProSkin
You can be sure that many new techniques will be developed with
this new material when
ingenious modellers get their hands on it.
Polyurathane adhesive is very useful for all sorts of materials.
It needs no mixing, cures quickly and foams out to form filleted
joints.
More details on 'Mick's Chat' page.
Pilots; cloth bodies, cast heads & hands
prepainted ready to fly.
 |
 1/4.5 for our Hurricane
16" tall 130g
Harry Hurri £85
|
 1/4 for our RF4 17" tall 130g
Civilian Ray £80
|
.
 1/4 scale for our spitfire 17" tall
200g
Johnny £90
|
 1/4 scale WW1 17" 180g
McCudden £80
|
 1/4 1930's style 17"
200g
Tiger Terry £85
|
 1/4 WW1 17" 200g
Major Bloater £80
|
.
 1/3.5 WW1 for our Strutter 20" tall
300g
Adiran £99
|
 1/3.5 WW1 for our Strutter
20" 300g Cpt Blotto £99
|
.
 1/3 WW1 23" tall 350g
for Pup or Camel
David £99
|
|
 .  . 
1/3 1930's style 23" tall
Tiger David £99
|
.http://jimr33v3s.wix.com/pilots
Two pack Epoxy
paint in authentic colours.
!
ONLY 125ml COLOUR TINS LEFT !!!! NO HARDENERS,
ONLY ORDER IF YOU HAVE SOME HARDENER FROM
PREVIOUS ORDER.!
THIS RANGE IS NOW
DISCONTINUED.
BASE COLOUR TINS ARE 125 m
Approximate coverage is 11 sq ft.
Sorry we can not send any paint outside the UK.
Roundel Blue
|
|
Med Sea Grey
|
|
|
 |
|
|
Dark sea Grey
|
|
|
 |
White
|
|
RAF Dark Green
|
|
|
 |
Roundel Red
|
|
PC10 Brown
|
|
|
Sparkley
Silver
|
|
PC 12 Brown
|
|
|
|
|
|
RAF Dark Earth
|
|
|
|
NOTE. The colours
look very dark on the screen, but are correct, see photos of my
model.
For Spitfires Use Dark Green and Dark Sea Grey for top.
Medium Sea Grey for bottom.
Sky for band at the rear. Yellow for leading edge and roundel
outer ring. Blue and white for roundels.
The red will serve for the roundels, but needs added yellow to be
fully authentic.
These colours are matched to existing Spitfire MH434 at Duxford.
For Sopwiths use PC10 for top surfaces, Linen Solartex for
the bottom.
These are matched to samples from RAF museum at Hendon.
Red, white, and blue for roundels.
One good system for painting a model is to use gloss for the main
colours. This gives good
adhesion for any decals to be used. Finally a clear coat in
Gloss, Satin, or Matt to give an even
finish and protection for the decals.
MR EPOXY is best sprayed on. Normal precautions should be taken.
You don't want to breath the vapours, or get the paint on your
skin.
The paint will need to be thinned for spraying, 20% to 40%.
Normal cellulose thinners is OK, and different grades are
available from motor factors.
.
.
